| |
Lars
Dallas, TX
Jan 9, 2012
|
WORKED FOR ME!
I used this cheap and simple solution to mount a Garmin zumo 660 GPS on the center clamp of my Ducati Multistrada's handlebar, and it worked exactly as advertised. Very happy with the price, quality & service.
Recommend? YES
5 viewers found this helpful. Was this review helpful to you?
Yes
No
|
| |
George
Georgia
Dec 12, 2011
|
EXCELLENT MOTORCYCLE MOUNT SOLUTION
Pros: economically priced and excellent quality.
Cons: none.
After looking at various mounts and even a bunch of RAM mounts, this item was brought to my attention. It is the typical RAM quality....excellent. The price is great when compared to other solutions. I think it is not so well known and therefore not used that often. I just recommend using a torque wrench when fastening if it replaces a handlebar mount, as it did on my bike.
Recommend? YES
6 viewers found this helpful. Was this review helpful to you?
Yes
No
|
| |
GZ
Springfield, VA
Nov 16, 2011
|
WORKS GREAT!
Pros: simple, cheap, works great
Cons: ball does squish over time, but doesn't affect it
What a simple solution for motorcycles! Fits KTM's and also my Yamaha FZ1.
Recommend? YES
9 viewers found this helpful.
|
| |
ByronH
Cypress,TX
Nov 4, 2011
|
HAVING A BALL WITH RAM MOUNTS
Customizing my Silverwing with numerous mounting options and Ram mount fits the bill. Able to add GPS, Iphone and drink holder.
Recommend? YES
9 viewers found this helpful.
|
| |
V-Biker
Detroit Lakes, MN
Oct 4, 2011
|
GREAT MOUNTING BRACKET
Pros: worked perfectly for my v-star 650 motorcycle
Cons: none
I purchased this for my V-Star 650 and it fit perfectly, even the chrome cap fits back on to hide the bolt. Used it on a 700 mile trip with my GPS and no problems at all!
Recommend? YES
19 viewers found this helpful.
|
| |
Alex
Vancouver BC
Sep 23, 2011
|
RAM MOUNT MOTORCYCLE HANDLEBAR CLAMP RAM-B-367U
Great but bolt doesn't fit Harley, wrong thread pitch, should come with extra in my opinion.
Recommend? YES
28 viewers found this helpful.
|
| |
cwayneb
Lexington, KY
Sep 8, 2011
|
SIMPLE, CLEAN, & A GREAT VALUE
Pros: everything
Cons: none
I purchase two of these when they were first introduced to install on my bikes. Everything about them is perfect as far as I'm concerned. Very clean look and always availalbe when needed. Way better than an ugly "U" type clamp on the handlebars.
Recommend? YES
37 viewers found this helpful.
|
| |
Trail_Time
PA
Sep 2, 2011
|
CLEAN SIMPLE AND STRONG
Pros: price, included bolts, durability, look
Cons: none
Not sure why this product has any negative reviews. The install is very clean. I put two of these on my PWC. One for GPS and one for a video camara. As all RAM mounts they are durable and do not slip. I have already logged over a hundred miles in the ocean and surf so it has been put thru a good test.
Recommend? YES
26 viewers found this helpful.
|
| |
Dave
Reno
Aug 26, 2011
|
SIMPLE AND WORKS GREAT
Pros: simple, works well, inexpensive
This ball mount is much easier to deal with than a handlebar clamp. Won't slip. Doesn't take up any space. I already have too much stuff on the bars, this makes things more tidy.
Recommend? YES
36 viewers found this helpful.
|
| |
Mike
San Jose, CA
Aug 22, 2011
|
SIMPLE AND WORKS
Pros: easy to install
Cons: small chuncks missing from edge
This product works great and is simple to install.
Recommend? YES
34 viewers found this helpful.
|
| |
Dean
New Westminster
Aug 4, 2011
|
MULTISTRADA
Works in the handlebar plate of my Ducati Multistrada and is a great unit!
Recommend? YES
36 viewers found this helpful.
|
| |
Frank
Vancouver, BC
Jul 21, 2011
|
NOT STURDY ENOUGH
Cons: rubber ball squishes
These need to be redeisgned. They do not stand up to anything more than medium pressure. The fact that the center of the rubber ball is drilled out to accomodate the bolt head, weakens the ball. It collapses (or squishes) if you really tighten an arm on to it. It needs to be a solid rubber ball, or harder rubber etc. I purchsed a replacement for this from a different company and it had a solid rubber ball and no squishing yet.
Recommend? NO
51 viewers found this helpful.
|
| |
MaxiMoto
Neenah, WI
Jun 28, 2011
|
JUST WHAT I NEEDED
Pros: effective low cost base mount.
Cons: rubber was a bit shabby around the mounting hole.
The perfect RAM Base Mount for my new Ducati Multistrada 1200. Fits on the handlebar clamp like it was made for the bike.
Recommend? YES
46 viewers found this helpful.
|
| |
A
New West
Jun 13, 2011
|
GOOD PRODUCT
Pros: installation and look
Cons: may not meet oem strength of original bolt design.
Easy to install. Works well.
Recommend? YES
57 viewers found this helpful.
|
| |
Jim
Toronto
Jun 6, 2011
|
RAM MOUNTING BALL GPS
This item is used to mount my GPS to my BMW R1200RT, fits just like it's suppose to, remove one bolt & replace with RAM Ball/Bolt. Can't get any easier.
Recommend? YES
56 viewers found this helpful.
|
| |
Motogirl
Rhode Island
May 13, 2011
|
VERY GOOD PRODUCT AND NOT MY FIRST PURCHASE!
Pros: ease of use and well made.
Cons: none
A well made and easy to use product. Very sturdy, doesn't vibrate, fits the handlebar mount perfectly and comes with 3 different length bolts. I have bar risers on my bike so the choice of bolt length was really great.
Recommend? YES
83 viewers found this helpful.
|
| |
drdave39
West Chester OH
May 5, 2011
|
SIMPLE IDEA, WORKS WELL
This really is a well-thought through product. It is easy to install, let's my Zumo mount solidly in a perfect locattion, and is almost invisible when not in use.
Recommend? YES
58 viewers found this helpful.
|
| |
TunaPete
Miami, FL
Apr 18, 2011
|
A SIMPLE SOLUTION
Pros: a clean look, like it came with the bike.
Cons: restricts mount position to the handlebar clamp.
After replacing the handlebars on my motorcycle, there was no longer room to mount the U-shaped handlebar RAM mount that I had originally installed on the bike. Upon discovering the availability of this Handlebar Clamp RAM Mount, I realized that it provided a simple and neat solution to the problem.
I have only used the current mount for a short while, so I cannot attest to its durability, but I had used the previous mount for several years and tens of thousands of miles, with no problems. My GPS even remained securely mounted to the bike through a violent accident with a delivery truck, so I presume the new mount is similarly durable.
One nice touch with this mount is that it comes with several lengths of hex-head handlebar clamp screws, so there should be one to match the length of the threads on the original screws on the bike. I've read some reviews that complained about the finish of the recessed hole in the ball, but the one I received looks fine.
Recommend? YES
75 viewers found this helpful.
|
| |
Bill
Philly, PA
Apr 7, 2011
|
SIMPLE AND EFFECTIVE MOUNT.
Pros: very inexpensive, well made, and simple.
Cons: none.
This little mount is about the cheapest, simplest way to add a RAM mount-point to your motorcycle. I installed as a direct replacement for one of my handlebar screws on a 1999 BMW R1100 RT, and it fits and works perfectly. There are three screws included with the ball mount, so it will easily replace a screw on a variety of metric bikes, probably in a variety of locations.
Recommend? YES
78 viewers found this helpful.
|
| |
Carl
New York
Mar 25, 2011
|
RAM MOUNT MOTORCYCLE RAM-B-367U
Pros: nice simple solution.
I put this on a 2007 BMW RT. The first one I received had a flaw in that it continually loosened no matter how much or often you tightened it. The good People at GPScity.com exchanged it promptly and the replacement works with a tidy excellence. The supplied bolts contained one of the right length. it installed easily, and turned out to be the perfect solution for me. Simple, clean, efficient. I'm very happy with it.
Recommend? YES
82 viewers found this helpful.
|
| |
coyo
Hamilton, ON
Mar 9, 2011
|
QUALITY CONTROL HAS NOT GOTTEN BETTER.
Pros: funtionally clean, professional mount.
Cons: aesthetically it looks like a cheap hack job.
I ordered this mount as the perfect, clean solution for my Super Duke... and it is.
But the low quality control of the aesthetics of the ball have not improved. It looks like my 5 year old cut the hole.
Functionally it's fantastic and as long as the arm and mount are on its deficiencies are barely visible.
[IMG]http://img.photobucket.com/albums/v44/coyo2/IMG-20110309-00122.jpg[/IMG]
GPS City was once again fantastic in their service and delivery.
Recommend? YES
78 viewers found this helpful.
|
| |
Michael
Ft Worth
Dec 10, 2010
|
TERRIFIC
Pros: low profile and simple.
Cons: black steel bolts in the kit. i used stainless.
I love this. It fits my motorcycle without being bulky or intrusive. I did replace the bolt I used with a stainless steel one. This one is on a 2008 Triumph Bonneville T100. I plan on using one on my Sprint ST 1050 too.
Recommend? YES
87 viewers found this helpful.
|
| |
Rob
Victoria BC
Nov 29, 2010
|
FITS PERFECTLY
Pros: nice tidy look
Cons: finish is a little rough
bolted right into the recessed bolt hole on my Triumph Sprint GT handlebar. choice of 3 bolt lengths make this a very vesatile product. also consider the "stubby" RAM mount for a nice tidy fit.
Recommend? YES
86 viewers found this helpful.
|
| |
John
Finger Lakes area of New York
Nov 8, 2010
|
REPLACED MY U-BOLT RAM MOUNT WITH THIS
Pros: simple, sturdy, nice looking, blends in nice
Cons: no cons yet.
Bought two and replaced the two lower handlebar clamp bolts with the Ram ball and bolt. Looks clean, simple and solid. I'm very happy. I just hope the black finsh on the bolts is durable.
Recommend? YES
89 viewers found this helpful.
|
| |
Tjp
Everett,WA
Oct 30, 2010
|
WATCH BOLT STRENGTH
Pros: great product helps immensely
Cons: the bolts are lower strength than stock
The Kawasaki bolts and the Genmar risers bolts are 10.9 strength. The Ram bolts are 8.8. So a significant reduction in strength for a critical part. 12.9 parts might have been a better deal even if it increases the cost 20 cents ...
Recommend? YES
106 viewers found this helpful.
|
| |
redhededgreg
Portland, OR
Oct 25, 2010
|
RAM MOUNT B-367U
Pros: price and clean, simple install.
Cons: none
No quality problems as noted in some other reviews. This provided the inexpensive, clean solution to a GPS mount I was looking for on my '09 R1200RT. I use a Cortech tank bag and can still view the GPS over the tank bag with no problem.
Recommend? YES
86 viewers found this helpful.
|
| |
geoffster
So Cal
Oct 18, 2010
|
LESS CLUTTER
Pros: easy!
Cons: i trimmed the flange to make it lower-profile.
I use this on a handlebar bolt on my BMW G650X. Much cleaner than the typical RAM clamp!
Recommend? YES
88 viewers found this helpful.
|
| |
Mick
Vancouver, BC
Sep 14, 2010
|
RAM MOUNT MOTORCYCLE HANDLEBAR CLAMP
Pros: easy install, comes with diff length boltsmi
Item was precisely what I needed to have a clean looking GPS mount on my V-Strom.
Recommend? YES
87 viewers found this helpful.
|
| |
Mike
Mount Horeb WI
Sep 9, 2010
|
QUALITY OF PRODUCT
The hole where the bolt goes into the ball is cut very poorly. It has jagged edges and looks cheap. I was going to call about it but did want to use it. The reviews said this item had a poor quality shipment to you. I asked about this when I ordered and was assured the poor quality ones had been sent back. Maybe most were but I did get a poor quality product that detracts from the appearance of the mount on the motorcycle.
Recommend? NO
85 viewers found this helpful.
|
| |
Peter
New York
Sep 6, 2010
|
RAM HANDLEBAR MOUNT
Pros: good fit and fuctional
Cons: strength of the alumimun
Works as described, the only weakness is the strength of the aluminum material. It deforms slightly when torque to specifications. It is minor and I don't believe it will compromise safety but a better grade of alloy should be used.
Recommend? YES
90 viewers found this helpful.
|
| |
Gary Earle
Oromocto
Sep 4, 2010
|
GPZ500S
Fit perfect for my GPZ....very solid, and came with the different lenght bolts so when I up grade my bike, I wont have any problems.
Recommend? YES
88 viewers found this helpful.
|
| |
Jon
Toronto
Aug 31, 2010
|
RAM BALL FOR GPS
Pros: cheap and works great
Cons: could be better quality
Quality of rubber is only OK (poorly trimmed, does not look like photo), but it was easy to install, and the price is excellent. It does the job.
Recommend? YES
101 viewers found this helpful.
|
| |
Dog
Callander, ON
Aug 17, 2010
|
TWO WORDS: QUALITY CONTROL
Mount works great, some vibration but nothing to worry about. The trimming around the bolt hole is done by hand and possibly by drunken Parkinson's patients. All cosmetic issues, function is fine.
Recommend? YES
86 viewers found this helpful.
|
| |
SpartanDen
Lansing, MI
Aug 13, 2010
|
DOES EXACTLY WHAT I WANT...
Pros: clean looking, less obtrusive
Cons: metric only fasteners, had to trim a bit
I bought this mount in an effort to "clean" up my bars and I DID NOT like the u-bolt style clamp. This is less intrusive. I have heard complaints about the finish of the mount. I am happy with this mount and its appearance. I did have the "tube" at the bottom of the mount trimmed up. This looks like it is designed to fit a european m/c and fit into the bar clamp. I trimmed it up and found a longer stainless US type fastener and mounted it up just fine. Works well, and does exactly what I want....holds my GPS securely.
Recommend? YES
87 viewers found this helpful.
|
| |
Rick
Red Wing, MN
Aug 6, 2010
|
I LOVE THIS GIZMO!
Pros: keeps a clean look on the handlebars.
Cons: none
I think this is the best motorcycle ball mount I've ever had. I have always hated the look of having stuff clamped to my handlebars and this simple device is the ticket. I found absolutely nothing wrong with the quality of the bolts or the finish of the ball.
Recommend? YES
104 viewers found this helpful.
|
| |
Chris
Olympia WA
Jul 23, 2010
|
FUNCTIONAL
Pros: works properly
Cons: plan to buy supplemental bolts
The supplied bolts are poor quality and the longest one was too short for my uses. Plan to buy a supplemental bolt, preferably in stainless steel. This means you're spending $10 for a small piece of rubbery plastic, which is a bit of a rip-off, but what do you expect for a motorcycle part? Otherwise it's your basic rubbery RAM ball mount and works well. This kit could also be used to mount a ball to any surface where you can drill a hole.
Recommend? YES
104 viewers found this helpful.
|
| |
Brent
Vancouver
Jul 19, 2010
|
BMW R1200RT GPS MOUNT
Pros: inexpensive
Cons: none
Used this to mount Zumo 550 to RT. Very clean neat install.
Recommend? YES
109 viewers found this helpful.
|
| |
Mario
Yarmouth, NS
Jul 19, 2010
|
RAM-B-367U HANDLEBAR CLAMP
Just what the doctor ordered. Installed with ease.Just pick the correct bolt and off you go. Clean installation and gets rid of the bulky clamps.
Recommend? YES
104 viewers found this helpful.
|
| |
BigJohn
Lenoir City, TN
Jul 14, 2010
|
RAM MOUNT MOTORCYCLE HANDLEBAR CLAMP RAM-B-367U
Pros: small and unobtrusive when not in use.
Very easy install, clean look, works fine. I like.
Recommend? YES
118 viewers found this helpful.
|
| |
john
denver
Jul 12, 2010
|
RAM B 367U
Pros: best mount i have found
Cons: looks like they have addressed most of them.
I had left a less than flattering review of this item. GPS City customer service department called me the very next day and asked how they might correct the problem. They offered and shipped me replacement parts the next day. I received and inspected them upon arrival. I am glad to report they are vastly better than any of the previously shipped parts including all the past orders I have made for them. I will say these were much improved but not perfect. In email exchanges I have had with GPS City they indicated that they are examining the cost versus quality issue on this item. It is my opinion the customer (certainly this one) would much rather pay a little more and receive a perfectly finished part than have a less finished one for less.
Recommend? YES
120 viewers found this helpful.
|
| |
john
denver
Jul 1, 2010
|
NO QUALITY CONTROL
Pros: none
Cons: all the above
I have purchased a number of these RAM balls and the finish on the moulded ball was never great but with some detailing were acceptable. This new order of four has resulted in one useable after extensive work including some time in my lathe to remove the scars left on the aluminum and the hatchet job done by the factory trimming the rubber. I will not be ordering this item again. I scrapped the three remaining parts. GPS city has been an amazing company that I always regarded highly but you may want to consider screening these before shipping your customers this rubbish.
[Ed. note: We have removed the stock of this part from our shipping warehouse for review. We are working very close with RAM to resolve the ball issue.
Once RAM have approved the quality of a new production run (expected to be completed Friday, July 02, 2010) we will update our inventory to the new, higher quality part and place this item back into stock for shipping.]
Recommend? NO
108 viewers found this helpful.
|
| |
Lauren
Orlando
Jul 1, 2010
|
THE BATCH I RECEIVED WAS BAD
Pros: neat way to mount a ram
Cons: quality i got was terrible
The image that you see, of this product? With the finely finished ball? Well, mine was NOT like that. I've included some links to what I got.
http://www.cyclepathic.com/images/ram_ball_1.jpg http://www.cyclepathic.com/images/ram_ball_2.jpg
I sent an email to the RAM mount folks about the quality control, but I have not heard back. GPS City was Awesome, as they always are. These balls were in this sorry state from the factory, so I didn't take this up with GPS City.
Recommend? NO
121 viewers found this helpful.
|
| |
Jason
Milwaukee, WI
Jun 1, 2010
|
HD MOUNT
Works great on the riser mount. The bolts that came with are metric. I had to go to HD dealership to get one with a STD thread pitch in order to use it.
Recommend? YES
130 viewers found this helpful.
|
| |
blackdot
New Glasgow, Nova Scotia
Jun 1, 2010
|
RAM MOUNT MOTORCYCLE HANDLEBAR CLAMP
Having the different length bolts included makes this item great. It works wonderfully on my Honda VTX1300R.
Recommend? YES
125 viewers found this helpful.
|
| |
panda
chicago
May 24, 2010
|
NOTHING IS PERFRECT SO QUIET COMPLAINING
Pros: very small profile. perfect.
Ok this went on my 2009 honda shadow aero 750 with out a problem. this is the simplest moun you can get for your gps. I used the smallest arm socket system and a garmin craddle and it sits right in the center of the handle bars. I just put it on last night and i will be making a Youtube video so everyone can see how it really looks on your bike. Look for Kawaskisisleeper on you tube it will be up tuesday night 5/25/2010. Thank GPSCity. good doing bussiness with you.
Recommend? YES
146 viewers found this helpful.
|
| |
Fleg
New Mexico
May 17, 2010
|
DOESN'T FIT ANYTHING.
Pros: would be nice if if it would fit anything
Cons: not easy to mount.
The product description is very vague. Out of all the motorcycles I own, it would only fit one bike on the handlebar clamp but only after I drilled out a hole for it. So, it sits on a shelf.
Recommend? NO
120 viewers found this helpful.
|
| |
matt
aurora, il
Apr 26, 2010
|
TOO LOW
not high enough - ball is even with my crossbar (wr250r) and limits rotation of the ram arm. Still works, but not ideal.
Recommend? NO OPINION
120 viewers found this helpful.
|
| |
tweak89
Houston, Tx
Apr 20, 2010
|
GREAT ADDTION TO THE RAM LINE!!
Pros: unobtrusive, easy install
I have avoided using RAM mounts on my motorcycles as I do not care for the look of the standard universal handlebar mount.
I came across this product in a random google search for GPS mounts.
It is a a marked improvement over the U-Bolt style mount. I this installed on my FZ6 and Star 950 so I can swap my Garmin GPS between the two.
Recommend? YES
110 viewers found this helpful.
|
| |
Wally
Midwest
Apr 15, 2010
|
GREAT IDEA!
Pros: saves time, saves space and reduces clutter
Cons: won't work on every bike
Of all the RAM ball mounts I have used, and that would be all of them this one is perfect and out of the box works better than the ones I had to cobble together from using other mounts as the base.
Recommend? YES
120 viewers found this helpful.
|
| |
John
Vancouver, BC
Apr 12, 2010
|
GREAT IDEA, EXECUTION NEEDS WORK.
Pros: easy to install, instant ram mounting on your bike
Cons: substandard finish detracts from aesthetic appeal
This is a pretty basic item, consisting of a partial RAM ball and three different length M8 bolts. Threads right into many handlebar or triple-tree mounts, giving you an instant, inexpensive and clean RAM mounting point. I installed it on my 2002 Triumph Sprint using the shortest of the supplied bolts.
Given the price of the item, it's not too upsetting that the visual appeal of the item is lacking. The plastic used on the ball has rough edges, and the finish on the mounting bolts is less than ideal (mine came black anodized, with a rough surface). The good news is, once you have your gadget mounted, you can't see it at all.
Recommend? YES
128 viewers found this helpful.
|
| |
Brisco
De Soto, Kansas
Apr 7, 2010
|
EXACTLY WHAT I WAS LOOKING FOR.
Pros: simple, unobtrusive
Cons: none
I was looking for a good way to mount a GPS on my Versys. I like this clean ball mount that will let me easily swam out my GPS for my video cam.
I knocked it down a star due to what others mentioned, having to trim rubber away from the bolt hole to get the bolt in. I wish it was as clean as the pics show...
Recommend? YES
126 viewers found this helpful.
|
| |
Eric
Denver, CO
Apr 7, 2010
|
PERFECT MOUNT FOR MY MOTORCYCLE
Pros: easy to install. perfect fit.
Cons: none
I'd been using a handlebar mount for my Garmin zumo 550 for over a year, but discovered this little guy. It was a perfect fit for my Ducati monster and puts the Garmin in a much more natural postion for when you're riding. It also frees up my cramped handlebars.
Recommend? YES
129 viewers found this helpful.
|
| |
Gary Burgdorf
Evansville, IN
Apr 5, 2010
|
GOOD IDEA
This is the best idea for mounting RAM systems to motorcycles I have seen to date. It mounts out of the way with no new U-bolts on the handle bars. Perfect.
Recommend? YES
124 viewers found this helpful.
|
| |
TML
Mpls, MN
Mar 8, 2010
|
MOTORCYCLE RAM MOUNT
I prefer this mount over the previous U-bolt mount I had on my V-Strom. With this mount in place and my GPS installed it looks great. This mount completes my instrument cluster modifications adding a voltmeter, gear indicator, heat troller and GPS.
Recommend? YES
143 viewers found this helpful.
|
| |
CK
Memphis, TN
Feb 25, 2010
|
PERFECT FUNCTION - NOT SO PERFECT QUALITY
Pros: great function and positioning
Cons: poor quality rubber.
I purchased a pair of these and waited a little over a month for them when they were first released by RAM. The mounting location is great and the function/positioning is much better than my old RAM mounts that attached to my brake and clutch reservoir clamps. My complaint is the quality of the mount/ball itself. The rubber was rough all over and required a lot of trimming to get it in working order (so the mounting bolt would fit, etc). I was not impressed at all with the appearance of the rubber coating. I have used them non the less and do like them. I am ordering another pair tonight in hopes they have a better appearance.
Recommend? YES
151 viewers found this helpful.
|
| |
Loff
Corona, CA
Feb 9, 2010
|
GREAT WAY TO MOUNT A GPS ON A MOTORCYCLE
Pros: ease of use and a good clean look.
Cons: none
I have two motorcycles and the Ram Mounts work great on both bikes. I just bought the new type of ball that attaches via one of the top clamp bolts. I like the looks of the ball and the ease of use. I bought one for my dad and he likes the improvement over the U bolt style of ball attachment.
Recommend? YES
222 viewers found this helpful.
|
| |
Tink
So Cal
Feb 8, 2010
|
PERFECT
Pros: simple, effective
Cons: none
This is the perfect mount for any motorcycle with handlebat clamps. I put two on my bike, one for GPS and a second for radar.
Recommend? YES
144 viewers found this helpful.
|
| |
Rolf
STL MO
Feb 8, 2010
|
GREAT SPACE SAVER
Pros: different bolts
Cons: none
Bought this bolt to replace the typical ram mount that clamps to handlebar. Not only does this save space on the bar, but it looks much cleaner. Bought this for a vstrom, and am going to buy one for my wr250r.
Recommend? YES
170 viewers found this helpful.
|
| |
BMW Rider
Marion, VA
Feb 5, 2010
|
RAM-B-367U MOUNT
Pros: clean installation easy to install works great
Cons: disappointed in the poor quality rubber ball
The completed installation was neat, clean, and no holes drilled or modification to my new R1200RT. The function is just what I wanted. Product quality was less than expected and required some trimming of the rubber from the bolt hole before I could install the mount.
Recommend? YES
151 viewers found this helpful.
|
| |
Nice n Easy Rider
Chapel Hill, NC
Feb 5, 2010
|
HANDLEBAR RAM MOUNT
Pros: simple, well-made
Cons: none
This mount worked perfectly for me. Allowed me to mount my SPOT in a convenient location without interfering with either my view of the instruments or my tank bag. Installed quickly and easily.
Recommend? YES
167 viewers found this helpful.
|
| |
threecog
Lynchburg VA
Jan 27, 2010
|
HAVING A BALL...
Pros: clean mounting
Cons: had to purchase a longer bolt due to risers.
The handlebar clamp mounting ball works really well. I like it a lot better than the muffler clamp mount that came with my Zumo. It helped streamline the mounting process and left my Triumph Tiger bars uncluttered. The clamp position worked well leaving the gauges visible and the GPS protected behind the windscreen.
Recommend? YES
157 viewers found this helpful.
|
| |
Hung Thick
north east USA
Dec 19, 2009
|
FOUND WHAT I NEEDED
This item is exactly what I needed to mount my Garmin GPS in a quick, neat fashion on my Triumph Sprint ST. The bolt replaces one of the fasteners for the clip-on bars, and provides a ball that accepts most of the RAM clamps and accessories. An inexpensive, quality solution. Perfect!
Thanks
Recommend? YES
226 viewers found this helpful.
|
| |
Hung Thick
norht east USA
Dec 19, 2009
|
FOUND WHAT I NEEDED
This item is exactly what I needed to mount my Garmin GPS in a quick, neat fashion on my Triumph Sprint ST. The bolt replaces one of the fasteners for the clip-on bars, and provides a ball that accepts most of the RAM clamps and accessories. An inexpensive, quality solution. Perfect!
Thanks
Recommend? YES
212 viewers found this helpful.
|
| |
Chris H
Evansville, IN
Dec 17, 2009
|
RAM MOUNT MOTORCYCLE HANDLEBAR MOUNT RAM-B-367U
Pros: easy to install. unobtrusive when not in use.
This is the cleanest RAM mount I know of. And it works great on my Hypermotard! Comes with three different length bolts to accommodate most applications.
Recommend? YES
217 viewers found this helpful.
|
| |
Viperdad
Malibu, CA
Dec 16, 2009
|
THREAD
Pros: works great with the replacement bolt
Cons: i asked in advance for the buell correct bolt.
The mount is a great idea, However you may need to purchase the correct metric grade 8 bolt to install it in your triple clamp if you have a Buell.
The GPS looks professional.
Recommend? YES
232 viewers found this helpful.
|
| |
Dave T.
Visalia, CA
Dec 16, 2009
|
GREAT GADGET!
Pros: well designed, easy to install.
Cons: none
I mounted this on my BMW1200GS, mainly to get rid of the clunky U-Bolt mount. It's a very clean mount and the three different bolts supplied garaunteed I had the correct lenght for my handle bar clamp. It posistions my GPS so that none of my instruments are blocked.
Recommend? YES
203 viewers found this helpful.
|
|
(4.3/5.0 based on 70 ratings)
